Sort By:
Show:
-
The Ethernet Interface Module permits direct connection of the SignalFire Wireless Mesh Network to an Ethernet Network. The Ethernet Interface Module has 2 addressable ports and is designed to connect to a standard SignalFire Gateway Stick with little or no configuration necessary.
Direct connection to the SignalFire Gateway-in-a-Stick
Modbus TCP access to all data, supports up to 16 simultaneous server connections
Allows remote configuration/diagnostics using the SignalFire ToolKit
Power Over Ethernet (PoE) support with auto switchover to DC power supply
Wide input voltage range of 6-36VDC
Industrial Temperature range of -40 to +85C
Conformal coated electronics
Easy web page configuration
DB9 port for local connection to gateway
Small form factor DIN mount enclosure
Status LED�s
Ethernet 10/100 base TX with Auto Negotiation, and HP Auto MDIX. RJ45 Connector
Network Interface: Ethernet 10/100 base TX with Auto Negotiation, and HP Auto MDIX. RJ45 Connector
Network Standards: TCP/IP, DHCP, and HTTP
Power Supply: 6-36VDC (screw terminals) (80mA at 12VDC) and Power Over Ethernet with auto switchover
Serial Port: DB9 serial port provides direct connection to Gateway using the SignalFire ToolKit
Modbus TCP Server: The Modbus TCP server supports 16 simultaneous server Connections
Remote Access: Ethernet gateway module allows remote connection to the gateway and field devices for configuration and diagnostics.
-
The Gateway DIN Mount is an integrated device combining a high power SignalFire radio with the gateway electronics in a single DIN mounted package.
Features
RS485 Modbus RTU interface
Two configurable digital outputs for local alarming and control
RS232 configuration and debug port
RP-SMA Antenna port for connection to 900 MHz antennas
Two digital outputs for local signaling or alarming, internal logic to map any remote data to the outputs
Optional Ethernet Modbus TCP interface module
Optional Analog Output Module
Optional remote shutdown programmable control logic, no additional PLC required
Stores the most recent readings of all nodes in the network in Modbus format, register remapping supported
Supports remote node configuration
Remote HART sensor configuration using PACTware or Radar Master
Timesout readings from off-line sensors
Manages outbound communications
Internal Event logging
DIN Mount into existing panel boxes
6-36 VDC wide range power input
500 mW radio
Automatically configures as a star or mesh network
Class 1 Division 2 Certified, Groups C&D, Temperature Code T5. Certified to CSA C22.2 No. 213, Conforms to ISA 12.12.01
Operating Temperature: -40 – 85ºC
Humidity: 0 – 100% condensing
Power: 6-36 VDC
Data Interface: RS-485 Modbus RTU, or Modbus-TCP, RS 232 for configuration.
All readings are converted to Modbus registers and stored in the gateway.
Digital Outputs: Open collector, 30VDC and 1Amp max
Radio Power: 500 mW
Antenna Type: RP-SMA Connector
Receive Sensitivity: -105 dB
Frequency: 902-928 MHz license-free ISM band compliant with FCC Part 15 and IC.
Range: 3 miles (typical) much farther with careful placement.
Networks: Up to 65,520 separate networks.
Enclosure: DIN Mount
Safety Rating: Non-incendive, Class 1 Division 2 Groups C and D, T5.
Internal Diagnostics: Line voltage, signal strength, error conditions event logging.
-
This rugged, integrated device combines a high-gain antenna with gateway electronics in a single, easily mounted package.
Gateway Stick combats a common problem with RF networks, which are increasingly used to monitor and control remote devices over tens or hundreds of square miles. Gateways traditionally have different location requirements for their electronics module and antenna, making it necessary to place them separately. Gateway Stick is a revolutionary solution that combines them in one easy-to-install component.
Features
Optional Ethernet Modbus TCP interface
Optional Analog Output Module
Unique design integrates high-gain, omni-directional antenna and gateway electronics in one place
Tough materials withstand rugged outdoor environments
RS485 Modbus RTU interface
RS232 configuration and debug port
Optional remote shutdown programmable control logic, no additional PLC required
Stores the most recent readings of all nodes in the network in Modbus format
Times out readings from off-line sensors
Manages outbound communications
Reduces power consumption
Mounts with clamps, brackets, or standard electrical/plumbing fittings
500mW radio with high gain antenna
Automatically configures as a star or mesh network
Class 1 Division 2 (C1D2), Temp Code T5, Groups C&D. Conforms to ISA 12.12.01 and UL 916, Certified to CSA C22.2 No. 142 and CSA C22.2 No. 213